mousepull15

Patio Door Lock Repairs Over time, patio doors experience wear and tear that can lead to lock malfunctions. Fortunately, there are several simple and efficient methods that can restore your uPVC patio door's security. These easy fixes will ensure your home is secure, whether you realign the lock or clean the locking mechanism. Clean the Lock Patio doors are great for letting the outdoors in while keeping out the elements. However they could pose an issue for security in the event that the lock isn't working properly. Over time, wear and tear, hot and cold weather, dirt, and debris can cause your patio door lock to become difficult to operate. With a little effort you can ensure that your patio door's lock is always working in a proper manner. It is essential to first clean the patio door lock and all moving parts. This will help to remove any dirt or coatings that might be hindering the lock from working effectively. Start by wiping all the moving parts of your patio door lock with a wet cloth. Then apply a scouring pad or a damp, rough cloth to scrub the areas that are soiled of the door frame and frame. Then, wipe the lock down using a dry towel to remove any remaining moisture. Allow it to air-dry before using it. If you have an outdoor door that has a pin tumbler latch mechanism You can lubricate the lock by applying powdered graphite to the key or by using a lubricant made of Teflon, such as WD-40 Multi-Use Product. This kind of lubricant is easy to apply and it doesn't dissolve with time. If you're unable to find the correct lubricant for your lock, you can make use of a pencil with a more of a thicker tip. Insert the pencil in the lock, and shake it to distribute the graphite. Tracks for sliding patio doors require regular maintenance to ensure they're free of dirt, dust, and debris. They are particularly vulnerable to snow and ice, which can cause them jam or bind and make it difficult for your patio doors to open and close. The sliding rails of the patio door track and rollers can be cleaned by removing any weather stripping that is damaged or dirty and then cleaning it, before installing it. The same can be done for patio door rollers, which can be cleaned and then sprayed with a non-stick lubricant that will allow them to move freely. Lubricate the moving parts uPVC French Doors, similar to sliding patios, operate with 3 to 4 or sometimes 5 point locking mechanisms. These include the lock cylinder and handle that is operated with the key. These doors require maintenance, the lubrication of moving parts. This can be accomplished using an oil that is thin (never WD40) and is recommended to be done at least once per year. If the hinges aren't causing the problem it could be because the door isn't aligned. It may be rubbing or catching the strike plate's hole in the frame. Remove the strike plate and employ a sharp tool to increase the size of its mortise. This lets the latch sit properly in the hole, and also prevents getting caught or rubbing against the frame. While the cylinder is out of the way take a measurement of its width using the help of a book or piece wood that will fit in the adjustment screw gap above the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder, and the inner dimension runs from the center of the adjustment screw to the end of the cylinder. Verify the lock's width If your patio door latch is hard to turn, even after oiling and cleaning it's possible that it's not aligned with the strike plate. Verify that the door is balanced, and if the hinge screws are tight. In a lot of instances, moving the strike plate downwards or upwards could solve the issue. Most of the time, the issue occurs when the lock's strike is too small for the latch to properly engage. In this situation, you need to widen the opening with an hammer and chisel. Then, test the latch to ensure that it doesn't touch the jamb frame of the door or get caught on it. Before buying a replacement lock, you should first determine what kind of mortise lock you have. You can do this by looking at the faceplate of the lock and determining whether it is square or round. Then, take a look at the screw holes on the existing lock and note the size of each one. This information will help you find an alternative that is the same size and fits perfectly into the hole you have already. You'll need to identify the mortise lock and inspect it for any bends, scratches or other damage that requires to be repaired. A badly bent or damaged latch is more likely than one that has been used a lot to break. Replace the lock if it shows signs of damage. After you've determined the type of lock replacement you need It's time to begin the actual repair. The old handle and spindle must be removed from the patio door. Introduce patio door repairs . Start by installing the inside handle. Align it with the spindle, and then secure it into position using two bolts or screws. Install the exterior handle after the interior handle. After you've completed the steps then you can test the new handles to ensure they can be opened and closed easily and that the latch locks properly with the strike plate. Check the Strike of the Door. The door latch and strike plate are the two parts of the lock that work to ensure the latch secures the door. If they are not aligned properly and the latch doesn't latch the door shut properly. Fortunately, this problem is usually simple to fix. Check the holes for receiving of the strike plate to make sure they are clear of obstructions like dirt or plastic plugs. Then loosen the keeper screws that keep the strike plate in place and allow it to move vertically but not removing it from the frame of your door. Then, you can adjust the strike plate so that its receiving holes align with the latch hooks on the door latch. After the strike plate has been adjusted, tighten all screws and test if the door closes smoothly. Door strike plates can be a bit difficult to access for homeowners with sliding patio doors, but they're essential for locking and unlocking your door. The metal plates are situated at the top and bottom jambs of your door, which are where they help support the latch. The door latch is inserted into the strike plate, and it creates an airtight seal. If the strike plate is damaged or rusted, or if it is not installed correctly the latch might not lock the door properly. One common reason for a patio door lock to not close or not close is a misalignment between the latch and the strike plate. The easiest way to check for this is to perform the “lipstick test.” Apply some lipstick along the edge of the deadbolt, and then put masking tape on it. When you shut the door the lipstick will leave an impression on the tape that will show you exactly where the latch contacts the strike plate. If the mark is too high or low it is possible to alter the strike plate. If your sliding patio door locks are not working properly they can help keep your home safe from burglars. It is imperative to resolve this issue as quickly as you can. By following these simple steps, you can repair your patio door's lock and get it back to normal in no time.